中国电力 ›› 2022, Vol. 55 ›› Issue (6): 103-110.DOI: 10.11930/j.issn.1004-9649.202202038

• 电网 • 上一篇    下一篇

特高压直流输电线路极间搭接塑料薄膜的放电模拟试验

王胜辉1, 王玺铭1, 董兴浩1, 周军2   

  1. 1. 华北电力大学 新能源电力系统国家重点实验室,北京 102206;
    2. 中国电力科学研究院有限公司,北京 100192
  • 收稿日期:2022-02-16 修回日期:2022-04-11 出版日期:2022-06-28 发布日期:2022-06-18
  • 作者简介:王胜辉(1977—),男,博士后,副教授,从事电气设备在线监测与故障诊断研究,E-mail:hdwsh@ncepu.edu.cn;董兴浩(1994—),男,通信作者,硕士研究生,从事电气设备在线监测研究,E-mail:1808827649@qq.com
  • 基金资助:
    国家重点研发计划资助项目(重大科学仪器设备开发重点专项,2018YFF01011903)

Simulation Experiment on Discharge of Plastic Film Overlapping on UHVDC Transmission Lines

WANG Shenghui1, WANG Ximing1, DONG Xinghao1, ZHOU Jun2   

  1. 1. State Key Laboratory of Alternate Electrical Power System with Renewable Energy Sources, North China Electric Power University, Beijing 102206, China;
    2. China Electric Power Research Institute, Beijing 100192, China
  • Received:2022-02-16 Revised:2022-04-11 Online:2022-06-28 Published:2022-06-18
  • Supported by:
    This work is supported by National Key Research and Derelopment Program of China (Project of Major Scientific Instruments and Equipment, No.2018YFF01011903)

摘要: 为研究搭接在特高压直流输电线路上塑料薄膜的放电现象,并解释某±800 kV特高压线路闪络故障原因,通过分析塑料薄膜表面3个典型区域等值盐密研究了闪络电压与塑料薄膜干燥和淋雨、平铺与卷起状态的关系,并进行了1.0 m、2.0 m和11.5 m 3种间隙距离下的闪络特性试验。研究结果表明:表面湿润状态下,当间隙距离为1.0 m和2.0 m时,塑料薄膜平铺与卷起时的间隙闪络电位梯度分别为1.22 kV/cm和0.96 kV/cm、0.82 kV/cm和0.7 kV/cm;当间隙距离为11.5 m时,潮湿塑料薄膜的间隙闪络电位梯度为0.56 kV/cm。在受潮条件下,塑料薄膜卷起相比平铺更容易发生闪络,平均闪络电位梯度随距离增加而呈下降趋势。最后还对某±800 kV特高压现场线路因塑料薄膜短接导致3次重启均不成功的原因进行了分析。

关键词: 特高压, 直流输电, 塑料薄膜, 间隙距离, 闪络电位梯度

Abstract: In order to study the discharge phenomena of plastic film overlapping on UHV DC transmission lines and explore the cause of flashover fault of a ±800 kV UHV line, an experimental study is conducted on the flashover characteristics of plastic film with three different gap distances of 1.0 m, 2.0 m and 11.5 m, and the relationship between flashover voltage and plastic states, including dry and wet state, spreading and rolling state, is studied through analyzing the equivalent salt density of three typical areas on the surface of plastic film. The results show that, when the gap distance is 1.0 m and 2.0 m, the gap flashover potential gradients of wet plastic film are 1.22 kV/cm, 0.96 kV/cm, 0.82 kV/cm and 0.7 kV/cm respectively for the spreading out and rolling up state; When the gap distance is 11.5 m, the gap flashover potential gradient of the wet plastic film is 0.56 kV/cm. Under the condition of moisture, the plastic film in rolling up state is more prone to flashover than that in spreading out state, and the average flashover potential gradient decreases with the increase of gap distance. Finally, the causes for the failed three times of restart of a ±800 kV UHV line caused by short circuit of plastic film is analyzed.

Key words: UHV, DC transmission, plastic film, gap distance, flashover potential gradient