[1] 谢学武. 几台变压器的故障分析与处理[J]. 中国电力,2005,38(5):43-46. XIE Xue-wu. Analysis and processing of several failure transformers [J]. Electric Power, 2005, 38(5): 43-46. [2] 王乃庆.变压器绕组轴向压紧对短路强度的影响[J]. 变压器,1997,34(3):3-8. WANG Nai-qing. Influence of short-circuit strength of axial compression on transformer winding [J]. Transformer, 1997, 34(3): 3-8. [3] 何文林,陈金法,应高亮,等. 频响分析法测试变压器绕组变形的研究[J]. 中国电力,2000,33(12):39-42. HE Wen-lin, CHEN Jin-fa, YING Gao-liang, et al . A study on detecting winding deformation in transformers with FRA method[J]. Electric Power, 2000, 33(12): 39-42. [4] 邢海瀛,刘少宇,马继先,等. 变压器抗短路能力核算与治理[J]. 中国电力,2012,45(5):25-29. XING Hai-ying, LIU Shao-yu, MA Ji-xian, et al . Accounting and governance on anti short circuit of transformer [J]. Electric Power, 2012, 45(5): 25-29. [5] 汲胜昌,李彦明. 变压器负载条件下提取铁心振动信号基频成分方法的研究[J]. 电工电能新技术,2003,22(2):4-68. JI Sheng-chang, LI Yan-ming. Research of method of extracting the primary frequency component of transformer’s core vibration signal under loading condition[J]. Adv. Tech. of Elec. Eng. & Energy, 2003, 22(2): 4-68. [6] 剻狄正,万达,邹云. 直流偏磁对变压器的影响[J]. 中国电力,2004,37(8):41-43. PENG Di-zheng, WAN Da, ZOU Yun. Impact on the transformer by DC bias [J]. Electric Power, 2004, 37(8): 41-43. [7] 吴书有. 基于振动信号分析方法的电力变压器状态监测与故障诊断研究[D]. 合肥:中国科学技术大学,2009:5-15. WU Shu-you. Research of power transformer condition monitoring and fault diagnosis based on vibration signal analysis [D]. Hefei: University of Science & Technology of China, 2009: 5-15. [8] 陆瑾,金怡. 振动法在变压器绕组状态监测中的应用研究[J],中国电力,2008,41(12):23-25 LU Jin, JIN Yi. Research in monitoring of transformer winding by vibration method [J]. Electric Power, 2008, 41(12): 23-25. [9] 张赢,马宏忠,陈楷. 变压器空载振动分析及实测研究[J]. 中国电力,2012,45(5):30-33 ZHANG Ying, MA Hong-zhong, CHEN Kai. Study on the transformer no-load vibration [J]. Electric Power, 2012, 45(5): 30-33. [10] 程锦,李延沐,汲胜昌. 振动法在线监测变压器绕组及铁心状况[J]. 高电压技术,2005,31(4):43-45. CHENG Jin, LI Yan-mu, JI Sheng-chang. Application of vibration method on monitoring the winding and core condition of transformer [J]. High Voltage Engineering, 2005, 31(4): 43-45. |