皱纹铝套变形对挤包绝缘直流电缆电场分布的影响

doi:10.11930/j.issn.1004-9649.202004035

中国电力 ›› 2020, Vol. 53 ›› Issue (9): 141-149.DOI: 10.11930/j.issn.1004-9649.202004035

• 高压电缆及附件关键技术专栏 • 上一篇下一篇

皱纹铝套变形对挤包绝缘直流电缆电场分布的影响

张洪亮^1,2, 尹毅^1,2, 肖晋宇³, 侯金鸣³, 闫志雨⁴, 谢书鸿⁴, 胡明⁴

1. 上海交通大学电子信息与电气工程学院，上海 200240;
2. 电力传输与功率变换控制教育部重点实验室，上海 200240;
3. 全球能源互联网发展合作组织，北京 100031;
4. 中天科技海缆有限公司，江苏南通 226010

收稿日期:2020-04-07 修回日期:2020-05-18 发布日期:2020-09-09
作者简介:张洪亮(1987—)，男，通信作者，博士研究生，高级工程师，从事聚合物纳米复合绝缘材料性能与应用、电力设备状态检测与评估和固体介质空间电荷测量技术等研究，E-mail：zhanghongliang@sjtu.edu.cn
基金资助:
国家重点研发计划资助项目(±500 kV直流电缆关键技术，2016YFB0900701)；江苏省重点研发计划资助项目(±500 kV等级直流电缆设计与制造关键技术研发，BE2018090)；全球能源互联网集团有限公司和国家电网有限公司科技项目(SGGEIG00JYJS1900009)

Influence of Deformed Corrugated Aluminum Sheath on the Electric Field of Extruded Insulation DC Cable

ZHANG Hongliang^1,2, YIN Yi^1,2, XIAO Jinyu³, HOU Jinming³, YAN Zhiyu⁴, XIE Shuhong⁴, HU Ming⁴

1. School of Electronic Information and Electrical Engineering, Shanghai Jiao Tong University, Shanghai 200240, China;
2. Key Laboratory of Control of Power Transmission and Conversion(SJTU), Ministry of Education, Shanghai 200240, China;
3. Global Energy Interconnection Development and Cooperation Organization, Beijing 100031, China;
4. Zhongtian Technology Submarine Cable Co., Ltd., Nantong 226010, China

Received:2020-04-07 Revised:2020-05-18 Published:2020-09-09
Supported by:
This work is supported by National Key Research and Development Program of China (Key Technology of ±500 kV DC Cable, No.2016YFB0900701), Jiangsu Province Key Research and Development Program (Key Technology Research of Design and Manufacture of ±500 kV DC Cable, No.BE2018090), Science and Technology Project of Global Energy Interconnection Group Co., Ltd. and SGCC (Key Technologies and Development Roadmap of UHV High-capacity DC Submarine Cable, No.SGGEIG00JYJS1900009)

摘要/Abstract

摘要： 为研究高压直流电缆皱纹铝套受力变形对电缆绝缘结构造成的损伤，以及在运行过程中对电气性能的影响，针对500 kV直流电缆开展绝缘线芯热膨胀测试和皱纹铝套压扁试验，确定皱纹铝套变形在绝缘线芯表面造成的缺陷情况。建立有限元模型，分析绝缘场强分布随温差变化情况，以及皱纹铝套变形导致绝缘线芯表面缺陷后的场强分布情况。仿真结果表明：电缆在负载过程中绝缘场强随着绝缘温差的变化而变化，此外绝缘表面存在缺陷会进一步导致场强畸变，且畸变程度与外加电压和绝缘温差有关。

关键词: 直流电缆, XLPE绝缘, 皱纹铝套, 绝缘温差, 电场分布, 有限元分析

Abstract: In order to determine the possible damage to the cable insulation structure by deformed corrugated aluminum sheath of HVDC cable and its influence on the electrical performance during operation, thermal expansion test and radial pressure test were conducted on 500 kV DC cable to identify the concave defects on insulation surface caused by the deformation of corrugated aluminum sheath. A finite element model was established to analyze the variation of insulation field intensity distribution with temperature drop, and the field intensity distribution on the defected insulation surface caused by the deformed corrugated aluminum sheath. The finite element simulation results show that the insulation field strength of cable varies with the insulation temperature difference during the load process, and the defects on the insulation surface can further cause the field strength distortion, the extent of which is related to the applied voltage and insulation temperature difference.

Key words: DC cable, XLPE insulation, corrugated aluminum sheath, temperature drop, electric field distribution, finite element analysis

张洪亮, 尹毅, 肖晋宇, 侯金鸣, 闫志雨, 谢书鸿, 胡明. 皱纹铝套变形对挤包绝缘直流电缆电场分布的影响[J]. 中国电力, 2020, 53(9): 141-149.

ZHANG Hongliang, YIN Yi, XIAO Jinyu, HOU Jinming, YAN Zhiyu, XIE Shuhong, HU Ming. Influence of Deformed Corrugated Aluminum Sheath on the Electric Field of Extruded Insulation DC Cable[J]. Electric Power, 2020, 53(9): 141-149.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: https://www.electricpower.com.cn/CN/10.11930/j.issn.1004-9649.202004035

https://www.electricpower.com.cn/CN/Y2020/V53/I9/141

参考文献

[1] 李昭红, 阳林, 田野, 等. 高压直流电缆接头稳态温度场分布及其影响因素[J]. 中国电力, 2016, 49(2): 48–53
LI Zhaohong, YANG Lin, TIAN Ye, et al. Steady-state temperature field of HVDC cable joint and its influencing factors[J]. Electric Power, 2016, 49(2): 48–53
[2] 张洪亮, 张建民, 于洪淼, 等. 中国首根±525 kV XLPE绝缘直流电缆的设计与试验验证[J]. 南方电网技术, 2018, 12(1): 1–6
ZHANG Hongliang, ZHANG Jianmin, YU Hongmiao, et al. Design and test verification of China's first ±525 kV XLPE insulated DC cable[J]. Southern Power System Technology, 2018, 12(1): 1–6
[3] 马为民, 吴方劼, 杨一鸣, 等. 柔性直流输电技术的现状及应用前景分析[J]. 高电压技术, 2014, 40(8): 2429–2439
MA Weimin, WU Fangjie, YANG Yiming, et al. Flexible HVDC transmission technology's today and tomorrow[J]. High Voltage Engineering, 2014, 40(8): 2429–2439
[4] 兰莉. 温度对聚合物绝缘中空间电荷行为的影响[D]. 上海: 上海交通大学, 2015.
LAN Li. Effect of temperature on space charge distribution in polymer insulation[D]. Shanghai: Shanghai Jiao Tong University, 2015.
[5] HANLEY T L, BURFORD R P, FLEMING R J, et al. A general review of polymeric insulation for use in HVDC cables[J]. IEEE Electrical Insulation Magazine, 2003, 19(1): 13–24.
[6] 屠亦军, 张洪亮, 高震, 等. 脱气处理对交联聚乙烯中交联副产物及空间电荷特性的影响[J]. 绝缘材料, 2018, 51(4): 58–63
TU Yijun, ZHANG Hongliang, GAO Zhen, et al. Effects of degassing treatment on crosslinking byproducts and space charge characteristics in cross-linked polyethylene[J]. Insulating Materials, 2018, 51(4): 58–63
[7] 范路, 陈萌, 张洪亮, 等. 型式试验对高压直流电缆交联副产物迁移过程及电导特性的影响[J]. 电气工程学报, 2018, 13(11): 44–51
FAN Lu, CHEN Meng, ZHANG Hongliang, et al. Effect of type test on migration process of cross-linked by-products and conduction characteristics of HVDC cables[J]. Journal of Electrical Engineering, 2018, 13(11): 44–51
[8] 张洪亮, 张建民, 谢书鸿, 等. 高压直流陆缆及海缆用大截面型线导体纵向阻水方式研究及验证[J]. 高电压技术, 2017, 43(11): 3626–3633
ZHANG Hongliang, ZHANG Jianmin, XIE Shuhong, et al. Study and verification of large section and longitudinally water-blocking heteromorphic conductor for HVDC land and submarine cable[J]. High Voltage Engineering, 2017, 43(11): 3626–3633
[9] 赵健康, 樊友兵. 高压电缆缓冲层的设计与工艺研究[J]. 电线电缆, 2010(3): 17–21
ZHAO Jiankang, FAN Youbing. Study of the design and process of the buffer in HV power cables[J]. Wire & Cable, 2010(3): 17–21
[10] 汪传斌, 金海云. 高压XLPE绝缘电力电缆缓冲层与金属护层结构设计仿真计算与优化[J]. 电线电缆, 2018(3): 6–12, 16
WANG Chuanbin, JIN Haiyun. The structural design simulation and optimization of high voltage XLPE insulation power cable buffer layer and metal sheath[J]. Wire & Cable, 2018(3): 6–12, 16
[11] 崔江静, 梁芝培. 高压电缆非金属外护套故障测寻方法[J]. 中国电力, 2001, 34(2): 61–63, 77
CUI Jiangjing, LIANG Zhipei. Trouble-locating method of non-metallic external sheath for HV cable[J]. Electric Power, 2001, 34(2): 61–63, 77
[12] 谢书鸿, 傅明利, 尹毅, 等. 中国交联聚乙烯绝缘高压直流电缆发展的三级跳: 从160 kV到200 kV再到320 kV[J]. 南方电网技术, 2015, 9(10): 5–12
XIE Shuhong, FU Mingli, YIN Yi, et al. Triple jumps of XLPE insulated HVDC cable development in China: from 160 kV, to 200 kV and then 320 kV[J]. Southern Power System Technology, 2015, 9(10): 5–12
[13] 张洪亮, 谢书鸿, 尹毅, 等. 厦门柔直工程±320 kV直流电缆绝缘及外护层结构选型与论证[J]. 高电压技术, 2016, 42(10): 3139–3146
ZHANG Hongliang, XIE Shuhong, YIN Yi, et al. Selection and verification of insulation and sheath structure of ±320 kV DC cable for Xiamen flexible DC transmission project[J]. High Voltage Engineering, 2016, 42(10): 3139–3146
[14] 邓声华, 江福章, 刘和平, 等. 高压电缆缓冲层材料及结构特性研究[J]. 电线电缆, 2019(2): 19–27
DENG Shenghua, JIANG Fuzhang, LIU Heping, et al. Research on materials and structural characteristics of buffer layers for high voltage cable[J]. Wire & Cable, 2019(2): 19–27
[15] 应启良. 柔性直流输电系统用直流交联聚乙烯绝缘电缆导体最高温度提高到90 ℃的可行性[J]. 电线电缆, 2014(3): 1–4
YING Qiliang. Feasibility of raising the maximum conductor temperature to 90 ℃ of DC XLPE cables with rated voltages up to 320 kV for VSC system[J]. Wire & Cable, 2014(3): 1–4
[16] 杨黎明, 朱智恩, 杨荣凯, 等. 柔性直流电缆绝缘料及电缆结构设计[J]. 电力系统自动化, 2013, 37(15): 117–124
YANG Liming, ZHU Zhi'en, YANG Rongkai, et al. Insulation material and structure design of HVDC flexible cables[J]. Automation of Electric Power Systems, 2013, 37(15): 117–124
[17] 何金良, 彭琳, 周垚. 环保型高压直流电缆绝缘材料研究进展[J]. 高电压技术, 2017, 43(2): 337–343
HE Jinliang, PENG Lin, ZHOU Yao. Research progress of environment-friendly HVDC power cable insulation materials[J]. High Voltage Engineering, 2017, 43(2): 337–343
[18] 杜伯学, 侯兆豪, 徐航, 等. 高压直流电缆绝缘用聚丙烯及其纳米复合材料的研究进展[J]. 高电压技术, 2017, 43(9): 2769–2780
DU Boxue, HOU Zhaohao, XU Hang, et al. Research achievements in polypropylene and polypropylene/inorganic nanocomposites for HVDC cable insulation[J]. High Voltage Engineering, 2017, 43(9): 2769–2780
[19] 中天科技海缆有限公司. ±500 kV梯形型线导体皱纹铝套光纤复合直流电缆. ZL 201620964613.1[P]. 2017 – 03 – 08.
[20] 张洪亮, 尹毅, 谢书鸿, 等. 不同金属屏蔽形式XLPE高压直流电缆载流量计算与试验验证[J]. 高电压技术. https://doi.org/10.13336/j.1003-6520.hve.20200310012.
ZHANG Hongliang, YIN Yi, XIE Shuhong, et al. Calculation and testing research on current rating capacity of XLPE insulated HVDC cable with different metallic screen type[J]. High Voltage Engineering. https://doi.org/10.13336/j.1003-6520.hve.20200310012.
[21] 魏东. 电线电缆手册-第4册[M]. 北京: 机械工业出版社, 2017.
[22] 额定电压500 kV及以下直流输电用挤包绝缘电力电缆系统第1部分: 试验方法和要求： GB/T 31489.1—2015[S]. 2015.
D. C. extruded cable systems for power transmission at a rated voltage up to and including 500 kV—Part 1: test methods and requirements: GB/T 31489.1—2015[S]. 2015.
[23] 闫志雨, 赵洪, 韩宝忠, 等. LDPE复合介质抑制空间电荷机制及电导特性对电场分布的影响[J]. 中国电机工程学报, 2017, 37(14): 4254–4264
YAN Zhiyu, ZHAO Hong, HAN Baozhong, et al. Suppression mechanism of space charge in CB/LDPE composite and the influence of conduction characteristic on electrical field distribution[J]. Proceedings of the CSEE, 2017, 37(14): 4254–4264

皱纹铝套变形对挤包绝缘直流电缆电场分布的影响

Influence of Deformed Corrugated Aluminum Sheath on the Electric Field of Extruded Insulation DC Cable

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

[1]	程洋, 夏令志, 牛雷, 阮巍, 孙昊, 曹轩赫, 张世珉. 500 kV双联耐张瓷绝缘子串的串间放电现象[J]. 中国电力, 2024, 57(9): 231-237.
[2]	石雨鑫, 王泽忠, 赵九才. 柔性直流换流阀厅全模型电场多极子边界元分析[J]. 中国电力, 2021, 54(8): 60-67.
[3]	朱杰, 伍珈乐, 宋绪鹏, 卞星明. 不同排列的金属球在均匀电场中的仿真研究[J]. 中国电力, 2021, 54(5): 129-138.
[4]	赵鹏, 欧阳本红, 陈铮铮, 陈鸿, 饶文彬, 赵健康, 张皓. 直流电缆试验标准体系分析及±535 kV电缆系统试验中关键问题[J]. 中国电力, 2021, 54(4): 10-18,25.
[5]	胡明, 刘淑军, 杨建军, 谢书鸿, 张洪亮, 闫志雨. 挤包绝缘高压直流电缆应用现状与研究展望[J]. 中国电力, 2021, 54(4): 42-55.
[6]	李飞, 钟力生, 李文鹏, 高景晖, 任海洋, 张翀. 挤包绝缘高压直流电缆制造与应用中的径向梯度效应[J]. 中国电力, 2021, 54(4): 63-71.
[7]	杨卓然, 杜伯学, 李忠磊, 韩冲, 张程. 极性反转电压下非线性电导硅橡胶复合材料电荷积聚特性[J]. 中国电力, 2020, 53(9): 150-156,165.
[8]	郑一博, 徐党国, 秦逸帆, 马浩, 李学宝, 孙云生, 牛铮. 110 kV GIS同频同相交流耐压试验中三工位隔离开关内部电场分布特性[J]. 中国电力, 2020, 53(2): 43-48.
[9]	成新兴, 李帅英, 武宝会, 牛国平. 四塔合一式脱硫除尘设施在600 MW机组中的应用[J]. 中国电力, 2018, 51(2): 149-155.
[10]	邓玲惠, 康豫军, 王军民, 程勇明, 王必宁. 冲击载荷作用下阀门阀瓣断裂失效的有限元分析[J]. 中国电力, 2017, 50(1): 125-129.
[11]	邓玲惠，康豫军，王军民，程勇明，王必宁. 某超临界锅炉减温管翘曲变形及开裂原因的有限元分析[J]. 中国电力, 2016, 49(5): 72-75.
[12]	张宇娇，孔韬，苏攀，董晓虎，雷成华. 微地形条件下220 kV朝峰线覆冰断线机理分析[J]. 中国电力, 2016, 49(5): 1-7.
[13]	李昭红，阳林，田野，李立浧，傅明利，卓然. 高压直流电缆接头稳态温度场分布及其影响因素[J]. 中国电力, 2016, 49(2): 48-53.
[14]	谢芳，冯炳，郭勇，叶尹. 新型500 kV/220 kV混压四回路直线塔的设计与研究[J]. 中国电力, 2015, 48(8): 73-79.
[15]	陈成，潘峰，王灿灿，黄聪，张彤，黄静文. “D”型截面复合材料塔头输电塔结构特性研究[J]. 中国电力, 2015, 48(3): 99-102.

模态框（Modal）标题

皱纹铝套变形对挤包绝缘直流电缆电场分布的影响

Influence of Deformed Corrugated Aluminum Sheath on the Electric Field of Extruded Insulation DC Cable

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics