500 kV输电线路耐张线夹电接触计算及其发热研究

doi:10.11930/j.issn.1004-9649.2016.11.025.06

中国电力 ›› 2016, Vol. 49 ›› Issue (11): 25-30.DOI: 10.11930/j.issn.1004-9649.2016.11.025.06

500 kV输电线路耐张线夹电接触计算及其发热研究

包健康, 高波, 张血琴

西南交通大学电气工程学院,四川成都 610031

收稿日期:2016-08-26 出版日期:2016-11-10 发布日期:2016-12-09
作者简介:包健康（1990—）,男,重庆人,硕士研究生,从事电力系统安全运行研究。E-mail: q68962264@126.com
基金资助:
国家自然科学基金资助项目（U1234202）

Research on Electric Contact Calculation and Heating of 500 kV Transmission Line Clamps

BAO Jiankang, GAO Bo, ZHANG Xueqing

College of Electrical Engineering, Southwest Jiaotong University, Chengdu 610031, China

Received:2016-08-26 Online:2016-11-10 Published:2016-12-09
Supported by:
This work is supported by National Natural Science Foundation of China (No. U1234202).

摘要/Abstract

摘要： 针对500 kV架空线路线夹运行温度过高引起线夹脱断,造成停电的事故,以NY型耐张线夹为研究对象,分析了耐张线夹接触电阻的计算方法,建立了耐张线夹电接触温升的有限元模型,以此研究了电接触最高温度与接触压力的关系,同时探明了电接触内部到外部的温度变化规律。研究表明：随着压力增大,最高温度呈现先迅速下降后下降变缓的趋势,额定压力下电流600 A引起的最高温度为31.42 ℃;随着压力增大,最高温度先后出现在铝板与螺栓的电接触、铝板间电接触和铝板与螺栓的电接触;线夹电接触内外存在温差,但内外温度变化具有一致性,外表面温度可间接表达线夹的运行温度。最后利用试验验证了电接触计算方法和仿真结果的正确性。

关键词: 耐张线夹, 电接触, 接触电阻, 接触压力, 最高温度, 温差

Abstract: In order to solve the clamp breaking problems caused by high operating temperature of 500 kV transmission line clamps, the calculation method of clamp contact resistance is investigated based on the NY-type clamps, and a finite element model of clamp electric contact heating is established with ANSYS to study the relation between the maximum electric contact temperature and the contact pressure and the temperature variation from the internal to external of the clamp. From the studies, it is found that the maximum temperature tends to decrease rapidly first and slowly afterwards with the pressure increase, and the maximum temperature reaches 31.42 ℃ at I=600 A under rated pressure; With the pressure increase, the maximum temperature occurs successively on the electric contact between aluminum plate and bolt, and the electric contact between the aluminums, and the electric contact between aluminum plate and bolt; A temperature difference exist between the internal and external of clamps but their temperature varies consistently, so the external temperature of clamps can present indirectly the operating temperature of clamps. Finally, the calculation method and simulation results are verified by experiments.

Key words: clamp, electric contact, contact resistance, contact pressure, maximum temperature, temperature difference

中图分类号:

TM751

包健康, 高波, 张血琴. 500 kV输电线路耐张线夹电接触计算及其发热研究[J]. 中国电力, 2016, 49(11): 25-30.

BAO Jiankang, GAO Bo, ZHANG Xueqing. Research on Electric Contact Calculation and Heating of 500 kV Transmission Line Clamps[J]. Electric Power, 2016, 49(11): 25-30.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: https://www.electricpower.com.cn/CN/10.11930/j.issn.1004-9649.2016.11.025.06

https://www.electricpower.com.cn/CN/Y2016/V49/I11/25

参考文献

[1] 刘纯,陈红冬,欧阳克俭,等. 碳纤维复合芯导线耐张线夹断裂分析[J]. 中国电力,2015,48（10）：97-100.
LIU Chun, CHEN Hongdong, OUYANG Kejian, et al . Analysis on the strain clamp fracture of ACCC[J]. Electric Power, 2015, 48(10): 97-100.
[2] 丁永福,王祖力,张燕秉,等. ±800 kV特高压直流换流站阀厅金具的结构特点[J]. 高压电器,2013,49（9）：13-18.
DING Yongfu, WANG Zhuli, ZHANG Yanbing, et al . Design structure characteristics of valve hall fittings in the ±800 kV HVDC converter station[J]. High Voltage Apparatus, 2013, 49(9): 13-18.
[3] 徐元哲,王乐天,刘雪冬,等. 电力电缆接头测温系统的设计[J]. 高电压技术,2009,35（12）：2977-2982.
XU Yuanzhe, WANG Letian, LIU Xuedong, et al . Design of temperature measurement system for cable junction based on FBG[J]. High Voltage Engineering, 2009, 35(12): 2977-2982.
[4] 李雪. 耐热导线耐张线夹发热问题解决方案研究[D]. 北京：华北电力大学,2010：9-10.
LI Xue. Research on the solution to the problem of the heat- resisting wire strain clamp giving off heat[D]. Beijing: North China Electric Power University, 2010: 9-10.
[5] 林杰,刘刚,张海鹏,等. 架空线路并沟线夹温度分布研究[J]. 电力系统保护与控制,2013,41（24）：88-94.
LIN Jie, LIU Gang, ZHANG Haipeng, et al . Research of temperature distribution of overhead lines parallel groove clamp[J]. Power System Protection and Control, 2013, 41(24): 88-94.
[6] 李阳林,周龙武,张宇,等. 双分裂导线连接金具异常发热原因分析与研究[J]. 中国电力,2016,49（5）：35-38.
LI Yanglin, ZHOU Longwu, ZHANG Yu, et al . Analysis on the abnormal heating of the link fittings for double-bundled conductors [J]. Electric Power, 2016, 49(5): 35-38.
[7] 王财宝,盛戈皞,曾奕,等. 基于ZigBee技术的导线接头温度集群监测[J]. 电力自动化设备,2009,29（11）：45-49.
WANG Caibao, SHENG Gehao, ZENG Yi, et al . Cluster monitoring system of transmission line joint temperatures based on ZigBee technology[J]. Electric Power Automation Equipment, 2009, 29(11): 45-49.
[8] 任丽佳,盛戈皞,曾奕,等. 动态提高输电线路输送容量技术的导线温度模型[J]. 电力系统自动化,2009,33（5）：40-44.
REN Lijia, SHENG Gehao, ZENG Yi, et al . A conductor temperature model based on dynamic line rating technology[J]. Automation of Electric Power Systems, 2009, 33(5): 40-44.
[9] 任西春,朱宽军,刘超群. 特高压输电线路新型防舞器建模分析[J]. 中国电机工程学报,2011,31（16）： 96-101.
REN Xichun, ZHU Kuanjun, LIU Chaoqun. Modeling and analysis of new anti-galloping devices on UHV transmission lines[J]. Proceedings of the CSEE, 2011, 31(16): 96-101.
[10] 谢天喜,莫娟,彭宗仁,等. 750 kV输电线路耐张塔绕跳间隔棒结构优化[J]. 高电压技术,2011,37（7）：1656-1662.
XIE Tianxi, MO Juan, PENG Zongren, et al . Strcture optimization of spacers on jumpers of strain towers on 750 kV transmission line [J]. High Voltage Engineering, 2011, 37(7): 1656-1662.
[11] 厉天威,黄文京,何民,等. 有限元法在高压输电线路线夹能量损耗计算中的应用[J]. 电网技术,2011,35（4）：218-222.
LI Tianwei, HUANG Wenjing, HE Min, et al. Power loss calculation of clamps for high voltage transmission line by finite element method[J]. Power System Technology, 2011, 35(4): 218-222.
[12] MILENKO B, VALERY K, NIKOLAI M. 电接触理论、应用与技术[M]. 许良军,译. 北京：机械工业出版社,2010：46-49.
[13] GREENWOOD J A, WILLIAMSON J B P. Contact of nominally flat surfaces [J]. Proceedings of the Royal Society A Mathematical Physical & Engineering Sciences, 1966, 295(295): 300-319.
[14] 彭向阳,陈驰,饶章权,等. 基于无人机多传感器数据采集的电力线路安全巡检及智能诊断[J]. 高电压技术,2015,41（1）：159-166.
PENG Xiangyang, CHEN Chi, RAO Zhangquan, et al . Safety inspection and intelligent diagnosis of transmission line based on unmanned helicopter of multi sensor data acquisition[J]. High Voltage Engineering, 2015, 41(1): 159-166.
[15] 张文峰,彭向阳,陈锐民,等. 基于无人机红外视频的输电线路发热缺陷智能诊断技术[J]. 电网技术,2014,38（5）：1334-1338.
ZHANG Wenfeng, PENG Xiangyang, CHEN Ruimin, et al . Intelligent diagnostic techniques of abnormal heat defect in transmission lines based on unmanned helicopter infrared video[J]. Power System Technology, 2014, 38(5): 1334-1338.
[16] JACKSON R L, CRANDALL E R, BOZACK M J. An analysis of scale dependent and quantum effects on electrical contact resistance between rough surfaces[C]//Electrical Contacts (Holm), 2012 IEEE 58th Holm Conference on IEEE, 2012: 1-10.
[17] 产品集合技术规范（GPS）表面结构轮廓法表面粗糙度参数及其数值：GB/T 1031—2009[S]. 北京：中国标准出版社,2009.
Standardization Administration of China. Product specifications set surface contour method(GPS) Surface texture roughness parameters and their values: GB/T 1031-2009 [S]. Beijing: China Standard Press, 2009.
[18] 张辉,韩学山,王艳玲. 架空输电线路运行载流量分析[J]. 电网技术,2008,32（14）：31-35.
ZHANG Hui, HAN Xueshan, WANG Yanling. Analysis on current carrying capacity of overhead lines being operated[J]. Power System Technology, 2008, 32(14): 31-35.

500 kV输电线路耐张线夹电接触计算及其发热研究

Research on Electric Contact Calculation and Heating of 500 kV Transmission Line Clamps

RichHTML

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 5

编辑推荐

Metrics

[1]	张洪亮, 尹毅, 肖晋宇, 侯金鸣, 闫志雨, 谢书鸿, 胡明. 皱纹铝套变形对挤包绝缘直流电缆电场分布的影响[J]. 中国电力, 2020, 53(9): 141-149.
[2]	贾志杰，张斌. GIS回路电阻超标缺陷定位分析[J]. 中国电力, 2015, 48(5): 46-50.
[3]	刘纯，陈红冬，欧阳克俭，唐远富，何朋飞，李文波，龚静. 碳纤维复合芯导线耐张线夹断裂分析[J]. 中国电力, 2015, 48(10): 97-100.
[4]	郑伟, 赵猛. 300 MW机组过热器喷水减温控制研究与改进[J]. 中国电力, 2014, 47(11): 26-29.
[5]	陈涛涛, 马宏忠. 双馈异步发电机电刷滑环电阻变化理论与仿真研究[J]. 中国电力, 2013, 46(12): 83-89.

模态框（Modal）标题

500 kV输电线路耐张线夹电接触计算及其发热研究

Research on Electric Contact Calculation and Heating of 500 kV Transmission Line Clamps

RichHTML

PDF (PC)

可视化

被引次数

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 5

编辑推荐

Metrics