大型电站烟风管道节能优化及工程应用

doi:10.11930/j.issn.1004-9649.201807042

中国电力 ›› 2019, Vol. 52 ›› Issue (7): 123-131.DOI: 10.11930/j.issn.1004-9649.201807042

大型电站烟风管道节能优化及工程应用

李昊燃, 徐永峰, 马翔

西安热工研究院有限公司, 陕西西安 710049

收稿日期:2018-07-12 修回日期:2019-01-10 出版日期:2019-07-05 发布日期:2019-07-13
作者简介:李昊燃(1992-),男,工程师,从事离心及轴流风机节能优化及改造技术研究,E-mail:18609286335@163.com
基金资助:
华能集团科技基金项目（燃煤机组烟气超低排放环保设施系统运行优化技术研究，HNKJ17-H11）。

Optimization and Engineering Application toward Energy Saving for Flue Gas Ducts in Large Coal-Fired Power Plants

LI Haoran, XU Yongfeng, MA Xiang

Xi'an Thermal Power Research Institute Co., Ltd., Xi'an 710049, China

Received:2018-07-12 Revised:2019-01-10 Online:2019-07-05 Published:2019-07-13
Supported by:
This work is supported by China Huaneng Group Science &Technology Fund (Research on Operation Optimization Technology of Flue Gas Ultra-low Emission Environmental Protection Facilities in Coal-Fired Units, No.HNKJ17-H11).

摘要/Abstract

摘要： 为探究大型火力发电厂烟风管道系统优化机理，利用数值模拟的方法，对所建方截面烟道和圆截面烟道模型的流场进行数值计算并分析。结果表明：方截面烟道的内撑杆后存在明显的尾迹涡流区，且流动稳定以后的直烟道有效流动面积仅为烟道截面总面积的79%左右；方截面直烟道和90°弯头的出口速度偏差分别为0.209、0.246，烟道压力损失严重；圆截面烟道内部流动分离相对减少，圆截面直烟道和90°弯头的出口速度偏差分别为0.052、0.146，与方截面烟道相比，压损减少60%以上。同时，通过对某300 MW电厂烟道改造项目的数值计算可知，经过将烟道截面优化为圆形和整体布置优化以后，烟道阻力下降了74.6%，内部流场均匀性得到改善，经济效益明显。

关键词: 火电厂, 烟道优化, 深度节能, 数值计算, 圆截面烟道

Abstract: To explore the mechanism of flue gas duct optimization for large coal-fired power plants, by virtue of numerical simulation, the flow fields of a square and a circular cross-section flue gas duct model are calculated and analyzed respectively. The result indicates that, there exists an obvious tail flow eddy zone behind the inner supports in the square cross-section flue gas duct, and the effective flow area of the straight duct is merely 79% of the total cross-section area after the flow is stabilized. The outlet velocity deviation is 0.209 in the square straight duct and 0.246 in the square bend, which shows substantial pressure losses. However, the outlet velocity deviation of the circular flue gas duct is 0.052 in the straight duct and 0.146 in the bend, which means that the flow separation is alleviated in the circular cross-section flue gas duct. Moreover, compared with the square cross-section flue gas duct, the pressure losses are lowered down by more than 60 percent. The numerical calculation of the flue gas duct reconstruction project of a 300 MW power plant shows that after the replacement of original square flue gas ducts with the circular ones and the overall layout optimization, the flue resistance has been decreased by 74.6% and the evenness of the flow fields has been improved. Therefore, great economic benefits have been achieved through the reconstruction project.

Key words: thermal power plant, flue optimization, deep power down technology, numerical calculation, circular-section flue gas duct

中图分类号:

TM621.7⁺3

李昊燃, 徐永峰, 马翔. 大型电站烟风管道节能优化及工程应用[J]. 中国电力, 2019, 52(7): 123-131.

LI Haoran, XU Yongfeng, MA Xiang. Optimization and Engineering Application toward Energy Saving for Flue Gas Ducts in Large Coal-Fired Power Plants[J]. Electric Power, 2019, 52(7): 123-131.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: https://www.electricpower.com.cn/CN/10.11930/j.issn.1004-9649.201807042

https://www.electricpower.com.cn/CN/Y2019/V52/I7/123

参考文献

[1] 中华人民共和国国家经济贸易委员会. 火力发电厂烟风煤粉管道设计技术规程:DL/T 5121—2000[S]. 北京:中国电力出版社, 2000:5−6. State Economic and Trade Commission of the People's Republic of China. Technical code for design of thermal power plant air and flue gas ducts/raw coal and pulverized coal piping:DL/T 5121—2000[S]. Beijing:China Electric Power Press, 2000:5−6.
[2] 钮旗超. 矩形烟风管道优化设计及其数据库开发[D]. 重庆:重庆大学, 2017.
[3] 樊晓康. 矩形烟风管道有限元建模及结构分析软件二次开发[D]. 重庆:重庆大学, 2017.
[4] 孙叶柱,孙伟鹏,江永. 1036 MW机组汽动引风机控制策略优化及其深度节能研究[J]. 中国电机工程学报,2011,31(增刊1):217-221. SUN Yezhu, SUN Weipeng, JIANG Yong. Research on optimizing the control strategy and deepening the energy conservation of steam-driven draft fans in 1036 MW unit[J].Proceedings of the CSEE, 2011, 31(S1):217-221.
[5] 刘家钰, 王宝华, 岳佳全, 等. 1000 MW机组引风机与脱硫增压风机合并改造研究[J]. 热力发电, 2010, 39(8):45-50 LIU Jiayu, WANG Baohua, YUE Jiaquan, et al. Study on retrofitting induced draft fan and FGD booster fan together for 1000 MW unit[J]. Thermal Power Generation, 2010, 39(8):45-50
[6] 高明帅, 张红侠, 马涛, 等. 超临界350 MW机组汽动引风机控制优化及其快速减负荷功能分析[J]. 热力发电, 2015, 44(4):44-49 GAO Mingshuai, ZHANG Hongxia, MA Tao, et al. Control optimization and runback analysis of steam-driven draft fans in a supercritical 350 MW unit[J]. Thermal Power Generation, 2015, 44(4):44-49
[7] 郑金, 程雁, 呼军, 等. 600 MW机组轴流风机静叶可调式改为动叶可调式方案研究[J]. 热力发电, 2016, 45(12):124-129 ZHEGN Jin, CHENG Yan, HU Jun, et al. Study and realization of transforming induced draft fans with adjustable stator blades into ones with adjustable rotor blades in a 600 MW unit[J]. Thermal Power Generation, 2016, 45(12):124-129
[8] 李江波, 贾绍广. 600 MW空冷机组锅炉烟风道优化设计分析[J]. 河北电力技术, 2010, 29(5):7-9 LI Jiangbo, JIA Shaoguang. Analysis on boiler flue gas ducts optimization design of 600 MW air-cooling unit[J]. Hebei Electric Power, 2010, 29(5):7-9
[9] 李少华, 白杰, 黄龙浩, 等. 大截面圆形烟风道设计方法研究[J]. 沈阳工程学院学报(自然科学版), 2017, 13(2):116-123 LI Shaohua, BAI Jie, HUANG Longhao, et al. Research of design methods of large cross-section area flue gas ducts[J]. Journal of Shenyang Institute of Engineering (Natural Science), 2017, 13(2):116-123
[10] 王观华. 国内首台自主型300 MW CFB锅炉烟风道布置优化设计[J]. 现代制造, 2010(18):217-218
[11] 李凯伦, 孙大伟, 朱红伟, 等. 600 MW火电机组烟道优化[J]. 热力发电, 2017, 46(4):120-124 LI Kailun, SUN Dawei, ZHU Hongwei, et al. Optimization of flue duct for a 600 MW thermal power unit[J]. Thermal Power Generation, 2017, 46(4):120-124
[12] 陈冠益, 耿页, 郑乐宇, 等. 带有内撑结构的电厂烟道弯头压力损失数值模拟[J]. 中国电机工程学报, 2013, 33(增刊1):153−159. CHEN Guanyi, GENH Ye, ZHENG Leyu, et al. Numerical simulation on pressure loss of power plant-based flue duct bend with inner supports[J].Proceedings of the CSEE, 2013, 33(S1):153−159.
[13] 韩卫冬. 烟风道内支撑优化设计[J]. 机电信息, 2011(15):174-175
[14] 罗永虹, 杨俊, 潘卫明. 90°方截面弯管的湍流计算[J]. 武汉大学学报(工学版), 2003, 36(2):62-65 LUO Yonghong, YANG Jun, PAN Weiming. Calculation of turbulent in 90° elbow pipe with square cross-section[J]. Engineering Journal of Wuhan University, 2003, 36(2):62-65
[15] 丁珏, 翁培奋. 90° 弯管内流动的理论模型及流动特性的数值研究[J]. 计算力学学报, 2004, 21(3):314-321 DING Jue, WENG Peifen. Numerical simulation of theoretical model and flow characteristics in 90° bending duct[J]. Chinese Journal of Computational Mechanics, 2004, 21(3):314-321
[16] 丁珏, 翁培奋. 三种湍流模式数值模拟直角弯管内三维分离流动的比较[J]. 计算物理, 2003, 20(5):386-390 DING Jue, WENG Peifen. Numerical study on three dimensional turbulent separated flow in right-angled curved duct by three turbulent models[J]. Chinese Journal of Computational Physics, 2003, 20(5):386-390
[17] 耿页. 低阻型烟风道数值模拟及内部流场的优化设计研究[D]. 天津:天津大学, 2014.
[18] 李昊燃, 董康田, 石清鑫. 进口气流速度分布不均对电站离心式引风机性能的影响[J]. 热力发电, 2017, 46(5):86-90 LI Haoran, DONG Kangtian, SHI Qingxin. Influence of inlet airflow maldistribution on the performance of double-sided centrifugal air fans[J]. Thermal Power Generation, 2017, 46(5):86-90
[19] 田原润, 马剑宇. 1000 MW机组烟气脱硝系统烟道流场优化[J]. 热力发电, 2018, 47(6):50-56 TIAN Yuanrun, MA Jianyu. Flue flow field optimization of flue gas denitration system in 1000 MW unit[J]. Thermal Power Generation, 2018, 47(6):50-56
[20] 张锋,王岩,孟德彪,等. 制粉系统热一次风道优化研究及工程应用[J]. 热力发电, 2018, 47(12):122-127 ZHANG Feng, WANG Yan, MENG Debiao, et al. Optimization of hot primary air duct for pulverizing system and its engineering application[J]. Thermal Power Generation, 2018, 47(12):122-127
[21] 祁轩,胡小彪,张志强. 1000 MW机组烟风道90°收缩弯头阻力特性分析[J]. 热力发电, 2017, 46(6):125-129 QI Xuan, HU Xiaobiao, ZHANG Zhiqiang. Resistance characteristics of 90° shrunk bend pipe connector of flue gas duct for a 1000 MW unit[J]. Thermal Power Generation, 2017, 46(6):125-129
[22] 谢龙汉, 赵新宇. ANSYS CFX流体分析及仿真[M]. 北京:电子工业出版社, 2013:8-14.

大型电站烟风管道节能优化及工程应用

Optimization and Engineering Application toward Energy Saving for Flue Gas Ducts in Large Coal-Fired Power Plants

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

[1]	刘习文, 彭卓寅, 胡新强, 叶泽, 何会学, 蔡睿, 魏文博. 燃煤火电厂年度燃料成本最小化决策模型及应用[J]. 中国电力, 2022, 55(6): 202-207.
[2]	晏敏, 张杨, 郭博闻, 朱跃. 基于全寿命周期成本的SCR脱硝系统优化分析[J]. 中国电力, 2021, 54(3): 191-196.
[3]	杨阳, 胡大龙, 黄倩, 许臻, 王璟, 吴火强, 王博. 火电厂废水排放控制政策法规与技术路线综述[J]. 中国电力, 2020, 53(8): 131-138.
[4]	邓宇强, 齐佶, 王启亮, 祁东东, 宋飞, 李海洋, 程家庆, 王冬梅, 马彦斌. 停用保护剂对锅炉启停期间水汽中TOCi的影响研究[J]. 中国电力, 2020, 53(6): 161-165,196.
[5]	王霂晗, 朱林, 张晶杰, 杨帆. 欧盟火电厂二氧化碳排放在线监测系统质量保证体系对中国的启示[J]. 中国电力, 2020, 53(3): 154-158,176.
[6]	何小锋, 刘晓锋, 卢修连, 华东奇, 马运翔, 何利鹏, 唐鹏涛. 润滑油交流油泵振动问题分析及治理[J]. 中国电力, 2020, 53(1): 169-176.
[7]	唐伟峰, 张佳琦, 李飞. 无磷阻垢剂WS330海水循环冷却阻垢试验研究[J]. 中国电力, 2019, 52(9): 161-166,178.
[8]	赵秀勇, 朱法华, 王圣, 孙雪丽, 徐静馨. 江苏省火电超低排放对环境空气中PM_2.5质量浓度影响模拟研究[J]. 中国电力, 2019, 52(9): 167-172.
[9]	段旭晨, 彭道刚, 姚峻, 赵慧荣, 夏飞. 基于SA-PSO-AHP的火电厂控制系统信息安全威胁评估[J]. 中国电力, 2019, 52(5): 29-35.
[10]	庞乐, 赵玉柱, 张帅, 李鹏. 加装低压省煤器对汽轮机排汽量的影响研究[J]. 中国电力, 2019, 52(4): 133-137.
[11]	韩超, 马欣欣, 沈维春, 董士波, 王秀娜, 曹旭, 徐剑锋. 智慧安全系统在火电厂中的应用研究[J]. 中国电力, 2019, 52(3): 127-132.
[12]	李玉宇, 吴火强, 余伟权, 毛进, 连坤宙. 珠海电厂精处理系统再生废水综合利用改造方案[J]. 中国电力, 2019, 52(3): 140-145.
[13]	肖育军, 邹毅辉, 李彩亭, 周雪斌. SCR系统结构模型与数值模型的适用性分析[J]. 中国电力, 2019, 52(3): 146-152,160.
[14]	张楚, 杨毅, 金格, 刘石, 高庆水. 循环水泵动态镜板翘曲故障诊断及振动评价讨论[J]. 中国电力, 2019, 52(2): 144-148,177.
[15]	王亚欧, 陶谦, 肖杰, 陈波. 1 000 MW双切圆燃烧锅炉干湿态转换过程中水冷壁温度控制[J]. 中国电力, 2019, 52(1): 161-165,173.

模态框（Modal）标题

大型电站烟风管道节能优化及工程应用

Optimization and Engineering Application toward Energy Saving for Flue Gas Ducts in Large Coal-Fired Power Plants

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics