DEH系统调节阀重叠度辨识及规范化整定方法

doi:10.11930/j.issn.1004-9649.201907017

中国电力 ›› 2020, Vol. 53 ›› Issue (2): 156-163.DOI: 10.11930/j.issn.1004-9649.201907017

DEH系统调节阀重叠度辨识及规范化整定方法

万忠海, 陈文, 蔡文, 鲁锦, 晏涛

国网江西省电力有限公司电力科学研究院, 江西南昌 330096

收稿日期:2019-07-01 修回日期:2019-07-25 出版日期:2020-02-05 发布日期:2020-02-05
作者简介:万忠海(1975-),男,高级工程师,从事电厂汽轮机试验与节能工作,E-mail:wzhjjch@163.com

Identifying and Standardized Setting Method of Overlap Degree of DEH System Regulating Valve

WAN Zhonghai, CHEN Wen, CAI Wen, LU Jin, YAN Tao

State Grid Jiangxi Electric Power Company Electric Power Research Institute, Nanchang 330096, China

Received:2019-07-01 Revised:2019-07-25 Online:2020-02-05 Published:2020-02-05

摘要/Abstract

摘要： 依据汽轮机原理，深入剖析了DEH系统调节阀重叠度的内涵及功能，建立了重叠度量化指标，确定并验证了阀位步进安全限幅是影响调节阀重叠度整定的关键性约束条件，提出了一种严格遵照既定阀序特性并脱离于压力重叠度且密切关联调节阀阀位的更为广谱适用的调节阀重叠度辨识及规范化整定方法。经仿真及现场试验验证，该方法满足调节阀重叠区域进汽流量线性度、DEH系统安全运行以及降低阀点工况节流损失的需求。

关键词: 汽轮机, 调节阀, 流量特性, 重叠度, 节流损失

Abstract: According to the principle of steam turbine, the connotation and function of the overlap degree of the regulating valve of DEH system are analyzed in-depth with the overlapping measurement indices established. Then the stepping safety limit of the valve position is determined and verified as the critical constraint affecting the adjustment of the valve overlap. Moreover, an applicable valve overlap identification and normalization setting method with broader spectrum is proposed in high compliance with the established valve sequence characteristics, which is separated from the pressure overlap and closely related to the valve position of the regulating valve. The simulation and field tests have verified that the method meets the requirements for the linearity of the inlet flow in the overlap area of the regulating valve, the operation security of the DEH system as well as the need to reduce the throttling loss under the valve point operating condition.

Key words: steam turbine, regulating valve, flow characteristics, overlap, throttling loss

万忠海, 陈文, 蔡文, 鲁锦, 晏涛. DEH系统调节阀重叠度辨识及规范化整定方法[J]. 中国电力, 2020, 53(2): 156-163.

WAN Zhonghai, CHEN Wen, CAI Wen, LU Jin, YAN Tao. Identifying and Standardized Setting Method of Overlap Degree of DEH System Regulating Valve[J]. Electric Power, 2020, 53(2): 156-163.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: https://www.electricpower.com.cn/CN/10.11930/j.issn.1004-9649.201907017

https://www.electricpower.com.cn/CN/Y2020/V53/I2/156

参考文献

[1] 王晓峰, 高春升. 600 MW汽轮机的阀门管理与调节级特性[J]. 汽轮机技术, 2003, 45(2):122-123 WANG Xiaofeng, GAO Chunsheng. 600 MW turbine valve management and governing stage performance[J]. Turbine Technology, 2003, 45(2):122-123
[2] 李宝玉, 魏毓璞. 汽轮机调节系统疑难问题解析[M]. 北京:化学工业出版社, 2006:283&-284.
[3] 文贤馗, 申自明. 汽轮机控制系统改造中调节阀重叠度的研究[J]. 热力发电, 2003, 32(5):41-43 WEN Xiankui, SHEN Ziming. Research on valve overlap degree in retrofit of steam turbine control system[J]. Thermal Power Generation, 2003, 32(5):41-43
[4] 沈士一. 汽轮机原理[M]. 北京:水利电力出版社, 1992:358.
[5] 许斯顿, 赖加良. 国产600 MW超临界汽轮机阀门流量特性曲线优化试验[J]. 发电设备, 2014, 28(2):128-132 XU Sidun, LAI Jialiang. Optimization of valve flow characteristic curves for domestic 600 MW supercritical turbines[J]. Power Equipment, 2014, 28(2):128-132
[6] 万忠海, 王小波, 汪飞, 等. 过载补汽节流配汽机组流量特性及重叠度试验研究[J]. 汽轮机技术, 2016, 58(3):211-214 WAN Zhonghai, WANG Xiaobo, WANG Fei, et al. Experimental study on the flow characteristics and overlap of the throttling units with additionally supplying steam at overload[J]. Turbine Technology, 2016, 58(3):211-214
[7] 李勇, 单丽清, 卢丽坤, 等. 某600 MW汽轮机配汽方式优化方法研究[J]. 汽轮机技术, 2013, 55(3):205-207 LI Yong, SHAN Liqing, LU Likun, et al. Research on the optimization of steam distribution mode of the 600 MW steam turbine[J]. Turbine Technology, 2013, 55(3):205-207
[8] 李勇, 单丽清, 徐世明, 等. 汽轮机调节汽门重叠度与节流损失之间关系的计算分析[J]. 汽轮机技术, 2013, 55(4):255-257 LI Yong, SHAN Liqing, XU Shiming, et al. The calculation and analysis on the relation of overlap and throttling losses for steam turbine's governing valves[J]. Turbine Technology, 2013, 55(4):255-257
[9] 张宝, 顾正皓, 樊印龙, 等. 通过试验计算汽轮机的流量特性[J]. 汽轮机技术, 2013, 55(3):215-218 ZHANG Bao, GU Zhenghao, FAN Yinlong, et al. Calculating the steam turbine flow characteristics through testing[J]. Turbine Technology, 2013, 55(3):215-218
[10] 万忠海, 晏涛, 吴杨辉, 等. 汽轮机流量特性试验原理及偏差、要点分析[J]. 汽轮机技术, 2015, 57(4):285-289 WAN Zhonghai, YAN Tao, WU Yanghui, et al. Analysis of turbine flow characteristics principle and bias and key points[J]. Turbine Technology, 2015, 57(4):285-289
[11] 李阳海, 张才稳, 杨涛, 等. 汽轮机调节阀流量曲线测试及流量管理函数优化研究[J]. 汽轮机技术, 2012, 54(5):368-371 LI Yanghai, ZHANG Caiwen, YANG Tao, et al. Steam turbine control valve flow curve measuring and flow dispatch function optimization research[J]. Turbine Technology, 2012, 54(5):368-371
[12] 万忠海, 晏涛, 鲁锦, 等. 汽轮机组变压运行热经济特性研究[J]. 中国电力, 2017, 50(12):81-86 WAN Zhonghai, YAN Tao, LU Jin, et al. Experimental study and application of steam turbine's variable pressure thermal economic characteristics[J]. Electric Power, 2017, 50(12):81-86
[13] 万忠海, 晏涛, 汪飞, 等. 汽轮机变压运行全局寻优试验方法[J]. 热力发电, 2013, 42(7):100-104 WAN Zhonghai, YAN Tao, WANG Fei, et al. Global optimization test method for variable pressure operation mode in steam turbines[J]. Thermal Power Generation, 2013, 42(7):100-104
[14] 中华人民共和国国家发展和改革委员会. 火力发电厂汽轮机电液控制系统技术条件:DL/T 996-2006[S]. 北京:中国电力出版社, 2006:16.

[1]	汪康康, 孙昕炜, 周波, 郑天文, 魏巍, 蒋力波. 基于压缩空气储能附加阻尼控制的电力系统低频振荡抑制策略[J]. 中国电力, 2023, 56(10): 115-123.
[2]	盛锴, 邹鑫, 邱靖, 朱晓星. 火电机组一次调频功率响应特性精细化建模[J]. 中国电力, 2021, 54(6): 111-118,152.
[3]	王志杰, 朱晓星, 王锡辉, 王志鹏. 基于LSSVM的汽轮机阀门流量特性辨识及应用[J]. 中国电力, 2020, 53(9): 189-194.
[4]	何国安, 胡相余, 杨铖, 安仕江, 张学延. 轴承振动对油膜涡动的影响分析与试验[J]. 中国电力, 2020, 53(7): 211-216.
[5]	崔亚辉, 姚剑飞, 徐亚涛, 渠福来, 孙鹏, 王增宏. 西门子1 000 MW汽轮机组轴系碰磨故障特性研究[J]. 中国电力, 2020, 53(6): 133-139.
[6]	徐章福, 邓彤天, 钟晶亮, 王锁斌, 张世海. 汽轮机DEH转速控制模式下的节能优化[J]. 中国电力, 2020, 53(4): 186-192.
[7]	张宝, 丁阳俊, 顾正皓, 应光耀, 樊印龙. 基于抑制电力系统低频振荡的火电机组控制方式优化[J]. 中国电力, 2020, 53(2): 137-141,149.
[8]	曲晓荷, 庄义飞, 张兴, 武海澄, 张剑, 李达. 基于逆向分段解耦的单顺阀切换过程流量特性建模及优化[J]. 中国电力, 2020, 53(12): 293-300.
[9]	杨文虎. 1 350 MW超超临界汽轮机技术特点及分析[J]. 中国电力, 2020, 53(1): 162-168,176.
[10]	梅益铭, 顾伟飞, 祝相云, 朱宝. 汽轮机阀门关闭试验中的噪声分析和信号处理[J]. 中国电力, 2019, 52(9): 154-160.
[11]	胡坚, 刘超. CPSO-FLN模型在汽轮机热耗率预测中的应用研究[J]. 中国电力, 2019, 52(8): 179-184.
[12]	胡坚, 刘超. 基于引力搜索算法与LSSVM的机组初压优化[J]. 中国电力, 2019, 52(6): 160-165.
[13]	吴昕, 李磊, 王争明, 梅隆, 宋亚军. 1 000 MW汽轮机快速冷却的应用与分析[J]. 中国电力, 2019, 52(2): 158-164,171.
[14]	牟春华, 吕凯, 许朋江, 孙大伟, 兀鹏越, 马汀山, 居文平, 李冬泉. 辅机统调动力源系统在某660 MW机组的应用[J]. 中国电力, 2018, 51(9): 65-72.
[15]	左智科, 陈国彬, 刘超, 牛培峰. 基于CNGWO-LSSVM的汽轮机热耗率预测模型[J]. 中国电力, 2018, 51(8): 148-153.

DEH系统调节阀重叠度辨识及规范化整定方法

Identifying and Standardized Setting Method of Overlap Degree of DEH System Regulating Valve

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

模态框（Modal）标题

DEH系统调节阀重叠度辨识及规范化整定方法

Identifying and Standardized Setting Method of Overlap Degree of DEH System Regulating Valve

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics