格构式复合材料电杆结构设计及承载性能分析

doi:10.11930/j.issn.1004-9649.2016.04.178.07

中国电力 ›› 2016, Vol. 49 ›› Issue (5): 178-184.DOI: 10.11930/j.issn.1004-9649.2016.04.178.07

• 电网 • 上一篇

格构式复合材料电杆结构设计及承载性能分析

杨风利¹，邢海军¹，李正¹，杨元春²

1.中国电力科学研究院，北京100192；
2.常熟风范电力设备股份有限公司，江苏常熟215554

收稿日期:2015-06-08 出版日期:2016-05-16 发布日期:2016-05-16
作者简介:杨风利（1980—），男，河北沧州人，博士，高级工程师，从事输电线路杆塔结构及防灾减灾研究工作。E-mail: yangfl1@epri.sgcc.com.cn
基金资助:
国家自然科学基金资助项目（51408568）

Structural Design and Bearing Capacity Analysis of a Lattice FRP Transmission Pole

YANG Fengli¹, XING Haijun¹, LI Zheng¹, YANG Yuanchun²

1. China Electric Power Research Institute, Beijing 100192, China;
2. Changshu Fengfan Power Equipment Co., Ltd, Changshu 215554, China

Received:2015-06-08 Online:2016-05-16 Published:2016-05-16

摘要/Abstract

摘要： 根据沿海台风地区气象条件，计算了大风工况下格构式纤维增强复合材料（FRP）电杆的设计荷载，确定了电杆结构布置型式和杆件规格。考虑服役周期内结构大变形和FRP老化的影响，采用通用有限元软件ANSYS完成了格构式FRP电杆结构分析；与承载性能相同的常规混凝土电杆相比，单根电杆重量可降低60%以上。为验证格构式FRP电杆的承载性能，完成了90°大风100%设计荷载工况和超载工况下的电杆结构真型试验，获得了沿高度方向的杆身位移和典型构件断面的应变，并与有限元计算得到的杆顶位移和主材断面应力进行了对比分析。研究结果表明，格构式FRP电杆杆件在250%设计荷载内均处于线弹性阶段，其中主材断面应力最大值159.8 MPa，低于FRP材料的屈服强度300 MPa；有限元计算得到的杆顶位移和主材断面应力与试验结果基本一致，当加载至约260%设计荷载时，FRP电杆根部侧面加固板孔壁发生剪切破坏。

关键词: 电杆, 格构式, FRP, D型截面, 真型试验

Abstract: According to the meteorological conditions in littoral typhoon areas, the designed load of a lattice FRP transmission pole is calculated under high wind condition, and the structural arrangement pattern and member sizes of the FRP transmission pole are determined. With consideration of the large deformation and aging effects of the FRP transmission poles in their service period, the general finite element analysis software(ANSYS) is used to make a structural analysis of the lattice FRP transmission pole. Comparing with the conventional reinforced concrete transmission pole, the weight of the FRP transmission pole can be reduced over 60%. In order to check the bearing capacity of the lattice FRP transmission pole, prototype tests are conducted respectively under 100% designed load and overloading condition with 90 degree high wind load. The displacements of the pole body along height direction and the strains at typical member sections are obtained and compared with the calculated displacements at the pole top as well as the stresses of main members by FEA method. It is indicated that when the testing load is less than 250% of the designed wind load, all the members are in linear elastic state with the maximum stress of the main members being 159.8 MPa, much lower than the yield stress of 300 MPa for FRP; the displacements at the pole top as well as the stresses of the main members calculated by FEA model are basically consistent with the testing values; when the testing load is over 260% of the designed wind load, shear failure occurs on the hole wall at the bottom of the lattice FRP transmission pole.

Key words: transmission pole, lattice, fiber reinforced polymer, D-type section, prototype test

中图分类号:

TB332
TM753

杨风利，邢海军，李正，杨元春. 格构式复合材料电杆结构设计及承载性能分析[J]. 中国电力, 2016, 49(5): 178-184.

YANG Fengli, XING Haijun, LI Zheng, YANG Yuanchun. Structural Design and Bearing Capacity Analysis of a Lattice FRP Transmission Pole[J]. Electric Power, 2016, 49(5): 178-184.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: https://www.electricpower.com.cn/CN/10.11930/j.issn.1004-9649.2016.04.178.07

https://www.electricpower.com.cn/CN/Y2016/V49/I5/178

参考文献

[1] 邵劲松，刘伟庆，蒋桐．民用工业中复合材料桁架的应用和发展[J]．玻璃钢/复合材料，２００６（５）：３５－３９．
SHAO Jinsong, LIU Weiqing, JIANG Tong. Application and development of composite trusses in civil industry[J]. Fiber Reinforced Plastics/Composites, 2006(5): 35-39.
[2] BAKIS C E, BANK L C, BROWN V L, et al. FRP composites for construction for construction—state-of-the-art review [J]. Journal of Composites for Construction, 2002, 6(2): 73-87.
[3] 刘泉，任宗栋，默增禄．纤维增强复合材料在35 kV输电杆塔中的应用研究[J]. 电力建设，２０１１，３２（４）：９２－９５．
LIU Quan, REN Zongdong, MO Zenglu. Study on application of FRP in 35 kV power transmission towers[J]. Electric Power Construction, 2011, 32(4): 92-95.
[4] 张兴虎，刘永辉，冯海潮． FRP管材轴心受压构件的稳定性能[J]．玻璃钢/复合材料，２０１４（２）：１９－２２．
ZHANG Xinghu, LIU Yonghui, FENG Haichao. Stable performance of FRP tube axial compression members[J]. Fiber Reinforced Plastics/Composites, 2014(2): 19-22.
[5] 杨林，王虎长，赵雪灵．复合材料在输电杆塔中的应用研究[J]. 中国电力，２０１４，４７（１）：５３－５６．
YANG Lin, WANG Huchang, ZHAO Xueling. Application research of FRP in the transmission structures [J]. Electric Power,2014, 47(1): 53-56.
[6] 陈成，潘峰，王灿灿，等． D型截面复合材料塔头输电塔结构特性研究[J]. 中国电力，２０１５，４８（３）：９９－１０２．
CHEN Cheng, PAN Feng, WANG Cancan, et al. Study on structural characteristics of transmission tower with the tower head of D-shaped composite material [J]. Electric Power, 2015, 48(3): 99-102.
[7] 岳平，王灿灿，韦立富，等． D型复合材料管轴压稳定承载力计算方法研究[J]. 中国电力，２０１５，４８（２）：７０－７５．
YUE Ping, WANG Cancan, WEI Lifu, et al. Study on calculating method of stable bearing capacity of D-shaped composite tube [J].Electric Power, 2015, 48(2): 70-75.
[8] Kinectrics Inc． Selected electrical tests on FRP poles manufactured by RS technologies[R]. Canada: Kinectrics Inc,2005．
[9] Sherif Mohamed Ibrahim. Performance evaluation of fiber reinforced polymer poles for transmission lines [D]. Manitoba: The University of Manitoba, 2011.
[10] 张磊，孙清，赵雪灵，等．纤维增强树脂基复合材料输电杆塔材料选型[J]. 电力建设，２０１１，３２（２）：１－５．
ZHANG Lei, SUN Qing, ZHAO Xueling, et al. Material selection for transmission tower made of fiber reinforced plastics [J]. Electric Power Construction, 2011, 32(2): 1-5.
[11] 李喜来，吴庆华，吴海洋，等．复合材料杆塔压杆稳定计算方法研究[J]. 特种结构，２０１０，２７（６）：１－５．
LI Xilai, WU Qinghua, WU Haiyang, et al. Study on the calculating method for compression stability of FRP tower members [J]. Special Structures, 2010, 27(6): 1-5.
[12] 王虎长，胡建民，赵雪灵．玻璃钢复合材料轴压构杆稳定性分析[J]. 电力建设，２０１１，３２（９）：８５－８９．
WANG Huchang, HU Jianmin, ZHAO Xueling. Stability analysis of axial compression component of FRP[J]. Electric Power Construction, 2011, 32(9): 85-89.
[13] 杨元春，谢佐鹏. 一种异型复合材料型材:中国专利，ZL 201110074333.5[P]. 2013-08-21.
[14] 杜柏松，葛耀君，周峥．复杂薄壁断面的自由扭转惯性矩的数值分析[J]. 同济大学学报：自然科学版，2006，３４（９）：１１７０－１１７４．
DU Baisong, GE Yaojun, ZHOU Zheng. Experimental research on performance of composite materials pole of 110 kV transmission line[J]. Journal of Tongji University: Natural Science, 2006, 34(9): 1170-1174.
[15] 10 kV及以下架空配电线路设计技术规定：DL/T 5220—2005[S]．

格构式复合材料电杆结构设计及承载性能分析

Structural Design and Bearing Capacity Analysis of a Lattice FRP Transmission Pole

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

[1]	黄郑, 顾徐, 王红星, 张星炜, 张欣. 基于改进PointNet++的输电杆塔点云语义分割模型[J]. 中国电力, 2023, 56(3): 77-85.
[2]	王宇航, 王文玲, 周绪红, 王康, 罗崯滔. 海上风电机组格构式浮式基础结构优化及响应分析[J]. 中国电力, 2022, 55(5): 21-31.
[3]	牛海军, 张雪松, 全姗姗, 刘胜春, 司佳钧. 特高压交流线路金具常见电晕位置及串型优化[J]. 中国电力, 2022, 55(2): 108-114.
[4]	汤奕, 徐香香, 陈彬, 易弢. 降雨滑坡灾害对输电杆塔故障的时空强在线预警[J]. 中国电力, 2020, 53(1): 56-65.
[5]	牛海军, 司佳钧, 周立宪, 朱宽军, 刘胜春, 朱小强, 史小龙. 特高压输电线路悬垂串金具优化研究[J]. 中国电力, 2019, 52(3): 95-101.
[6]	张宏杰, 李正, 杨风利, 韩军科, 宫博. 六边形输电塔体型系数与风荷载计算[J]. 中国电力, 2017, 50(3): 107-112.
[7]	程永锋，郑卫锋，张强，鲁先龙，丁士君. 输电线路装配式基础应用研究[J]. 中国电力, 2016, 49(8): 26-30.
[8]	杨勉, 商文念, 刘建秋, 郎需军. 国内外标准变电构架风荷载及风致响应对比[J]. 中国电力, 2016, 49(7): 39-44.
[9]	谢芳，陈驹，金伟良，冯炳. 钢混组合结构大跨越输电塔主柱和节点的试验研究[J]. 中国电力, 2016, 49(6): 120-125.
[10]	张宏杰，杨靖波，杨风利，张志军，朱乐东. 台风风场参数对输电杆塔力学特性的影响[J]. 中国电力, 2016, 49(2): 41-47.
[11]	陈成，潘峰，王灿灿，黄聪，张彤，黄静文. “D”型截面复合材料塔头输电塔结构特性研究[J]. 中国电力, 2015, 48(3): 99-102.
[12]	潘峰, 高志林, 王轶文, 聂建波, 应建国. 360°风作用下线条风荷载分配系数特性[J]. 中国电力, 2014, 47(10): 64-70.
[13]	韩军科. ±800 kV同塔双回输电线路十字组合角钢塔承载力真型试验[J]. 中国电力, 2014, 47(10): 1-6.
[14]	杨林, 王虎长, 赵雪灵. 复合材料在输电杆塔中的应用研究[J]. 中国电力, 2014, 47(1): 53-56.
[15]	张子富，杨靖波，杨风利，李清华. 重冰区特高压酒杯型钢管塔设计及试验[J]. 中国电力, 2013, 46(5): 45-50.

模态框（Modal）标题

格构式复合材料电杆结构设计及承载性能分析

Structural Design and Bearing Capacity Analysis of a Lattice FRP Transmission Pole

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics