基于累积损伤曲线的电寿命模型步进应力试验方法及在XLPE电缆中的应用

doi:10.11930/j.issn.1004-9649.202005062

中国电力 ›› 2020, Vol. 53 ›› Issue (9): 125-132.DOI: 10.11930/j.issn.1004-9649.202005062

• 高压电缆及附件关键技术专栏 • 上一篇下一篇

基于累积损伤曲线的电寿命模型步进应力试验方法及在XLPE电缆中的应用

边浩然, 杨丽君, 马志鹏, 丁志文, 李仲轩

输配电装备及系统安全与新技术国家重点实验室(重庆大学)，重庆 400044

收稿日期:2020-05-09 修回日期:2020-06-30 发布日期:2020-09-09
作者简介:边浩然(1994—)，男，博士研究生，从事电缆寿命预测、老化状态评估研究，E-mail：bhrcqu@sina.com;杨丽君(1980—)，女，通信作者，博士，教授，从事高压电器绝缘状态在线监测及故障诊断、电力变压器及电缆老化机理及诊断研究，E-mail：yljcqu@cqu.edu.cn
基金资助:
国家重点研发计划资助项目(±500 kV直流电缆关键技术，2016YFB0900701)

Step-Stress Test Method for Electrical Life Model Based on Cumulative Damage Curve and Its Application in XLPE Cable

BIAN Haoran, YANG Lijun, MA Zhipeng, DING Zhiwen, LI Zhongxuan

State Key Laboratory of Power Transmission Equipment & System Security and New Technology (Chongqing University), Chongqing 400044, China

Received:2020-05-09 Revised:2020-06-30 Published:2020-09-09
Supported by:
This work is supported by the National Key Research and Development Program of China (Key Technology of ±500 kV DC Cable, No.2016YFB0900701)

摘要/Abstract

摘要： 交联聚乙烯（XLPE）的反幂函数电寿命模型（IPM）表征了XLPE电缆绝缘的长期耐压特性，包括电压耐受指数（VEC）在内的IPM模型参数是电缆绝缘设计和预鉴定试验电压选取的重要依据。步进应力试验具有耗时短、效率高的优点，适用于求取电缆样品的电寿命模型参数。然而，步进应力试验参数的选择尚无规程可参考，目前主要依靠经验和主观确定，严重影响了试验结果的有效性和可比性。将固体绝缘材料累积损伤“D-t曲线”作为判断绝缘失效机理的主要依据，分析不同试验参数下步进应力与恒定应力试验的等效性，提出适合工程应用的步进应力试验参数选取及现场试验方案。通过该方法设计绝缘厚度分别为2.8 mm和3.5 mm的2种模型电缆的步进应力试验，并获取2种模型电缆的IPM电寿命模型参数，验证该方法的可行性。

关键词: 交联聚乙烯电缆, 电压耐受指数, 步进应力试验, 寿命模型

Abstract: The inverse power function electrical life model (IPM) of XLPE represents the long-term voltage endurance characteristics of XLPE cable insulation. The parameters of IPM model including voltage endurance coefficient (VEC) are the important basis for cable insulation design and pre-qualification test voltage selection. The step-stress test has the advantages of short time and high efficiency, and is more suitable for obtaining the electrical life model parameters of cable samples. However, there are no standards for selection of step stress test parameters. At present, it mainly depends on experience and subjective determination, which seriously affects the validity and comparability of test results. In this paper, the “D-t curve” of accumulated damage of solid insulating materials is taken as the main basis to judge the failure mechanism of insulation. The equivalence of step-stress test and constant-stress test under different test parameters is analyzed, and the step-stress test parameters and field test scheme suitable for engineering application are proposed. With this method, a step-stress test is designed for two types of model cables with insulation thickness of 2.8 mm and 3.5 mm respectively, and the parameters of IPM electrical life model for the two types of model cables are obtained, which validates the feasibility of the proposed method.

Key words: XLPE cable, voltage endurance coefficient, step-stress test, life time model

边浩然, 杨丽君, 马志鹏, 丁志文, 李仲轩. 基于累积损伤曲线的电寿命模型步进应力试验方法及在XLPE电缆中的应用[J]. 中国电力, 2020, 53(9): 125-132.

BIAN Haoran, YANG Lijun, MA Zhipeng, DING Zhiwen, LI Zhongxuan. Step-Stress Test Method for Electrical Life Model Based on Cumulative Damage Curve and Its Application in XLPE Cable[J]. Electric Power, 2020, 53(9): 125-132.

导出引用管理器 EndNote|Ris|BibTeX

链接本文: https://www.electricpower.com.cn/CN/10.11930/j.issn.1004-9649.202005062

https://www.electricpower.com.cn/CN/Y2020/V53/I9/125

参考文献

[1] KUBOTA T, TAKAHASHI Y, SAKUMA S, et al. Development of 500 kV XLPE cables and accessories for long distance underground transmission line-Part I: insulation design of cables[J]. IEEE Transactions on Power Delivery, 1994, 9(4): 1741–1749.
[2] Power cables with extruded insulation and their accessories for rated voltages above 150 kV (U_m=170 kV) up to 500 kV (U_m=550 kV) - test methods and requirements: IEC 62067–2011[S].
[3] Power cables with extruded insulation and their accessories for rated voltages above 30 kV (U_m=36 kV) up to 150 kV (U_m=170 kV) - test methods and requirements: IEC 60840–2011[S].
[4] Recommendations for testing DC extruded cable systems for power transmission at a rated voltage up to 500 kV: TB 496–2012[S].
[5] 高思航, 杨丽君, 邓帮飞, 等. 硫腐蚀对绕组绝缘电寿命的影响及导致绝缘失效的故障机制研究[J]. 高电压技术, 2020, 46(5): 1606–1615
GAO Sihang, YANG Lijun, DENG Bangfei, et al. The influence of sulfur corrosion on the electrical life of winding insulation and the failure mechanism of insulation failure[J]. High Voltage Engineering, 2020, 46(5): 1606–1615
[6] 杨丽君, 李仲轩, 姚人允, 等. 获取XLPE绝缘直流电压耐受指数的步进应力试验参数选取方法研究[J]. 电工技术学报, 2019, 34(24): 5244–5251
YANG Lijun, LI Zhongxuan, YAO Renyun, et al. Selection of step-stress test parameters for obtaining DC voltage endurance coefficient of XLPE insulation[J]. Transactions of China Electrotechnical Society, 2019, 34(24): 5244–5251
[7] 陈宇. 电气绝缘电压寿命指数N值的极大似然估计[J]. 吉林电力技术, 1999(2): 5–7
CHEN Yu. Maximum likelihood estimation of N value of electrical insulation voltage life index[J]. Jilin Electric Power, 1999(2): 5–7
[8] TIWANA A P S, REDDY C C. Life estimation using damage equalization method and step-stress breakdown tests[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2016, 23(4): 2311–2318.
[9] WANG Y, LV Z, WANG X, et al. Estimating the inverse power law aging exponent for the DC aging of XLPE and its nanocomposites at different temperatures[J]. IEEE Transactions on Dielectrics and Electrical Insulation, 2016, 23(6): 3504–3513.
[10] 欧阳本红, 刘松华, 邓显波, 等. 高压XLPE电缆绝缘厚度优化设计[J]. 高电压技术, 2016, 42(8): 2388–2393
OUYANG Benhong, LIU Songhua, DENG Xianbo, et al. Optimization design for insulation thickness of high-voltage XLPE cable[J]. High Voltage Engineering, 2016, 42(8): 2388–2393
[11] 柯春俊, 林春耀, 欧小波, 等. 步进电压下变压器匝间绝缘电压寿命指数新解法[J]. 哈尔滨理工大学学报, 2016, 21(5): 66–72
KE Chunjun, LIN Chunyao, OU Xiaobo, et al. New solving method for voltage endurance coefficient N of transformer turn-to-turn insulation under step-voltage[J]. Journal of Harbin University of Science and Technology, 2016, 21(5): 66–72
[12] MONTANARI G C, GHINELLO J, PERUZZOTTI F, et al. Endurance characteristics of XLPE compounds under DC voltage[C]//ICSD'98. Proceedings of the 1998 IEEE 6th International Conference on Conduction and Breakdown in Solid Dielectrics (Cat. No. 98CH36132). Vasteras, Sweden. IEEE, 1998: 439–442.
[13] CORPORATION J P SYSTEMS. HVDC XLPE cable systems applicable for higher temperature and[J]. 8th International Conference on Insulated Power Cables, 2011.
[14] WATANABE C, ITOU Y, SASAKI H, et al. Practical application of ±250 kV DC-XLPE cable for Hokkaido-Honshu HVDC link[J]. Electrical Engineering in Japan, 2015, 191(3): 18–31.

基于累积损伤曲线的电寿命模型步进应力试验方法及在XLPE电缆中的应用

Step-Stress Test Method for Electrical Life Model Based on Cumulative Damage Curve and Its Application in XLPE Cable

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 2

编辑推荐

Metrics

[1]	何文荣, 贺霄皖, 郑珊珊, 宋昕, 赵勇, 卫二兵. 采用OWTS检测10 kV交联聚乙烯电缆本体主绝缘损伤[J]. 中国电力, 2017, 50(8): 93-97.
[2]	杨明亮, 周凯, 尧广, 马建国. 水树老化XLPE电缆绝缘修复技术应用及展望[J]. 中国电力, 2014, 47(6): 61-65.

模态框（Modal）标题

基于累积损伤曲线的电寿命模型步进应力试验方法及在XLPE电缆中的应用

Step-Stress Test Method for Electrical Life Model Based on Cumulative Damage Curve and Its Application in XLPE Cable

RichHTML

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 2

编辑推荐

Metrics